The 1 b qut tn nhit dc 12v 30cm 3010 3cm 30x10mm 2pin is a compact linear actuator built for precise short-stroke applications in automotive and industrial environments. Its 12V DC operation and 30cm travel make it suitable for dashboard adjustments, seat modules, and compact machinery where dimensional constraints are critical.
This device pairs a slim 30x10mm profile with a 3cm stroke and 3010-style tubular design, while the 2pin connector simplifies integration. Below you can quickly compare key mechanical and electrical characteristics at a glance.
| Parameter | Value | Unit | Notes |
|---|---|---|---|
| Model Code | 1 b qut tn nhit dc | - | Internal reference for procurement and service |
| Supply Voltage | 12 | V DC | Nominal; verify polarity before wiring |
| Stroke Length | 30 | cm | Approx. 12 in, suitable for trim and tilt tasks |
| Body Diameter | 3 | cm | Outer tube width, influences cavity space |
| Mounting Footprint | 30 | x 10 | mm, compact profile for tight panels |
| Connector Type | 2pin | - | Pre-wired leads, polarized if specified |
| Typical Force | Variable | N | Depend on speed and load conditions |
| Ambient Temp Range | -30 | to +80 | °C, suited for under-hood environments |
12V DC Actuation Performance
Operating at 12V DC, this actuator emphasizes stable speed and consistent force delivery without requiring complex motor controllers. The low voltage simplifies integration with car batteries, auxiliary power supplies, and regulated bench supplies. Ensure the supply can deliver sufficient current to avoid voltage drop during peak load, and verify that inrush current aligns with fuse ratings.
Efficiency and Duty Cycle
For repeated trimming cycles, check the manufacturer’s duty cycle limits to prevent overheating. Short on-off intervals at full load may demand a higher-rated power supply or local thermal protection. Using correct polarity and strain relief on the 2pin feed reduces risk of intermittent operation or connector wear.
Mechanical Packaging and Integration
The 30x10mm outer body and 3cm travel allow the actuator to fit into dashboards, storage compartments, and seating trim modules where space is at a premium. The compact form minimizes cable slack requirements, while the 2pin layout keeps wiring harnesses clean and serviceable. Confirm mounting hole spacing and avoid lateral forces on the shaft to extend functional life.
Environmental Robustness
Designed for demanding surroundings, the unit tolerates wide temperature swings and moderate vibration. Sealing details and material choice help resist road salts and humidity; always verify compatibility with adjacent plastics to prevent chemical or mechanical interaction over time.
Application Scenarios and Selection Criteria
Use cases include adjusting instrument panel modules, folding levers, and compact actuation arms where a 30cm push or pull is enough. When comparing with longer-stroke or higher-force systems, prioritize compatibility with the host structure and connector layout. The 1 b qut tn nhit dc 12v 30cm 3010 3cm 30x10mm 2pin suits applications demanding fine position control rather than brute force.
- Confirm voltage compatibility with the host system (12V DC)
- Validate stroke and force against the intended mechanical load
- Check ambient temperature range for under-hood placement
- Verify connector orientation and wire routing to avoid strain
- Assess mounting clearance to prevent interference with adjacent parts
Installation and Wiring Guidance
Route cables neatly, use proper grommets, and secure connectors with clips or zip ties to prevent fatigue during repeated motion. Add in-line fuses and reverse polarity protection if the system lacks board-level safeguards. Label the 2pin leads at both ends to simplify future troubleshooting and reduce installation errors.
Key Takeaways and Next Steps
- Specify 12V DC with a 30cm stroke and 30x10mm profile for tight-panel installs
- Check peak current and duty cycle to size power supplies and fuses
- Use the 2pin connector with strain relief to maintain reliability
- Confirm mechanical loads stay within stated force limits
- Plan periodic inspections to catch wear early and extend service life
FAQ
Reader questions
Can I power the 1 b qut tn nhit dc 12v 30cm 3010 3cm 30x10mm 2pin from a car battery directly?
Yes, connect it to a stabilized 12V accessory point with an appropriately rated fuse; ensure the battery can supply peak current without sagging below the minimum voltage threshold.
What is the recommended maintenance interval for this actuator?
Inspect connectors and wiring for wear every 12,000 km or six months, and verify mechanical alignment if you notice uneven movement or increased noise during operation.
How do I confirm the correct polarity of the 2pin connector?
Refer to the service manual for the host system or use a multimeter to identify the positive and negative terminals before applying power.
Will using this actuator with an incorrect voltage damage it?
Applying voltage significantly higher than 12V DC can overheat coils and degrade seals; always match the supply to the rated voltage and use voltage regulators if needed.