How to Use This TV Codes Reference for Directv Remotes
This reference provides TV codes for Directv remotes in a clear, searchable format. If you want the fastest results, use the table to locate your TV brand and code, then follow the step-by-step entry instructions below the table. The steps work for most Directv remotes manufactured in the last decade, including remotes labeled as Genie or HR remotes. Note: Some newer TVs may require slightly different setup flows, but the code method below remains a recommended first troubleshooting step.
Quick Lookup: TV Codes for Directv Remote by Brand
| TV Brand | TV Code(s) for Directv Remote | Notes |
|---|---|---|
| Samsung | 0012, 0057 | 0012 is widely used; 0057 is an alternative |
| LG | 0016, 0115 | Try 0016 first; 0115 if unsuccessful |
| Sony | 0004, 0114 | 0004 is common for older models; 0114 for many newer ones |
| Vizio | 0910, 0996 | 0910 often works; 0996 as a fallback |
| TCL | 0018, 0101 | 0018 is common; 0101 may be needed for certain models |
| Roku | 0030 | Use 0030 for most Roku TVs; confirm with remote test |
| Panasonic | 0019, 0116 | 0019 often works; try 0116 if needed |
| Sharp | 0022, 0135 | 0022 is a common starting point; 0135 as alternative |
Step-by-Step: Entering a TV Code on Your Directv Remote
- Turn on your TV using its own power button or remote.
- Point your Directv remote at the TV.
- Press and hold the Setup button until the Status light blinks twice, then release.
- Enter the TV device code for your brand using the remote keypad (for example, 0 0 1 2 for Samsung 0012).
- The Status light should blink twice to confirm the code was accepted.
- Test the remote by pressing Power or Volume. If the TV powers off or responds, the code is working.
If the TV does not respond, repeat the process with the alternative code from the table for your brand. If neither code works, try the remote reset method described later in this article.
Understanding Device Types and Code Scope
TV codes for Directv remotes are programmed into the remote to match the communication protocol of your television. These codes are not universal; they vary by brand and, in some cases, by model year. A Directv remote is typically programmed for the TV, audio device, and cable box functions. This reference focuses on TV codes, but using the same remote for a soundbar or AV receiver may require different codes and a similar entry process. Always confirm the device type on-screen during setup if your remote offers device selection.
Troubleshooting When Codes Do Not Work
If a code fails to work, first confirm you entered the digits correctly and pressed Setup until the Status light blinked twice. Many issues are resolved by repeating the entry process with clear line-of-sight between the remote and the TV. If problems persist, try a remote reset to clear old or conflicting codes. You can also test the TV using its own remote to rule out TV-specific issues. For some models, firmware updates on the television or replacing remote batteries can restore infrared or RF functionality.
Performing a Remote Reset
To reset a Directv remote, follow these steps:
- With the remote pointed away from the TV, press and hold the Setup button until the Status light blinks twice.
- Enter 9 8 2. The Status light should blink twice again.
- Press the Power button once. The Status light should stay lit. If it blinks and turns off, repeat the steps and ensure you complete the sequence without long pauses.
After a reset, you will need to reprogram the remote using the TV codes table and reconfigure any other device codes (cable, audio) if needed.
When to Seek Further Support
Use this TV codes for Directv remote reference as a first-line troubleshooting tool before contacting support. If your remote still does not respond after trying two codes per device type and a remote reset, contact Directv support with your remote model number and TV brand. Having your TV model number and remote type ready can speed up resolution, as some newer TVs or sound systems require alternate code sets or firmware-based solutions.
Long-term Maintenance Tips for Remote Codes
Remote codes can occasionally change after firmware updates or battery replacements. Periodically verify that your remote commands are working as expected, especially after service calls or TV replacements. Keep this reference handy or save the codes for your most-used brands in a secure note on your phone. Establishing a simple routine test—such as powering the TV and adjusting volume once a month—can prevent frustration when you need the remote most.